Jul 26

A .The adjustment of the drum speed.

 

The adjustment of the bowl speed is performed in  manual adjustment or decanter centrifuge plate prescribed maximum working speed following the adjustment.

Different rated speed by installed different size wheel by diameter for driving the main belt wheel to set different drum operation speed

In variable frequency drive decanter centrifuge will paired with control panel that allow increase and decrease the drum speed.

By fine-tuning the speed of the drum, it can perform more precise solids particles separation.  It can also improve the wear of the drum, the vibration and the noise to extend the service life of the decanter centrifuge.

The separation purpose or drilling fluid solids content  is by the choice drum speed. For instance, barite recovery or processing high-density mud, it is suggested that the low spending  speed. For general medium density mud prefer choose medium or high speed.  The low density mud is ideal for using high speed decanting centrifuge.

decanter centrifuge-2

 

B. The adjustment of the differential drive

 

Centrifuge differential speed (back drive is also refer by) in its within the prescribed scope of, do not suggest user to adjust and it can only adjust in a small range change the parameters.

Different speed centrifuge adjustment methods are remove the original auxiliary motor pulley, and reloading large diameter or smaller diameter belt wheel  Auxiliary motor pulley  change the differential input shaft speed enhancement in result of differential speed decreased. On the other hand, it can also cause differential speed increase.

 

Operators must understand that regular maintenance on the centrifuge such as regular cleaning the inlet and outlet by filling water or diesel depends what kind of fluid it needs process.  It is also crucial that  add grease to the bearing parts to ensure proper lubrication.

GN Solids Control sell a series of solids control equipment and drilling waste management equipment including vertical cuttings dryer , shale shaker  , shear pump , oilfield shale shaker , mud cleaner , desander and desilter , vacuum degasser , Mud Gas Separator , decanter centrifuge , mud tank , mud agitator , etc . GN Solids Americal normally keep stock for GN main product and shale shaker , mud cleaner and decanter centrifuge always keep stock there to service local client .

Share

written by Decanter Centrifuge \\ tags: , , , , , ,

Jun 28

GN Solids Control is really a world famous solids control maker and drilling waste management turnkey provider.
This year GN Solids Control will sign up for many top oil and gas display. GN Solids Russia may attend the MIOGE 2016, which is one of the largest vitality shows in Russia along with Europe. Another branch firm GN Solids America may also attend the great OTC demonstrate.
This year the MIOGE is actually hold at EXPOCENTER within Moscow, Russia from Rate of interest. 18th to 21st. GN Solids Russia booth number is Pavilion-2, Hall-5, T 40.
Welcome to connect with GN Solids Russia for more info, GN Solids will give hot here you are at all GN old along with new friends in this demonstrate. GN Solids Russia is found at Г. Москва, Радонежского Сергия Ул. д. a couple of, please feel free to call +7-8(925)304 25 70 +7- 8(968)950 31 49 and make the reservation.
GN Solids Russian federation will exhibit the following tools:
1 . GN Mud Cleaner
GNJZ594E-3S16N will be exhibited with this show. This one compact solids control equipment with a few sets desanders and fourth there’s 16 sets desilters on the top of a single GN shaker. This GN shaker is using the same dimensions of Mongoose screens. GN also manufactures various shaker screens, such as replacement projection screens for Derrick, NOV, FSI etc .

Russia Oil Show
2 . GN Decanter Centrifuge
GNLW363 centrifuge is really a proven successful equipment that may be used to separate mud and also recovery barite. With Tungsten carbide tiles along the attach propellers and ceramics plug-ins, GN decanter centrifuge is far more resistance and can be used for a longer period.
3. GN Cuttings Dryer
GNCD930 cuttings dryer is especially used for OBM, SBM or even WBM separation. With these many years feedback from worksites, GN cuttings dryer has been replacing to separate all the cuttings via shale shaker, desilter.
GN Solids America LLC also has a couple booths in this year from the OTC show, one is from the NRG Center (booth number 1652-A) for GN Solids Control and another with the area for GN Solids America (booth no . 9732).

Share

written by Decanter Centrifuge \\ tags: , , , , ,

Jun 21

“GE, an industrial company, but also a digital company”. Some people may have watched this commercial on American’s main media, like CNN or NBC and we may wonder what does that mean? The answer is it represents the future trend-digital and automation.

As we all know, GE is the conglomerate in many industries, such as energy, electric appliances, aerospace and so on. So its action and strategy will represent the future of the industry. Recently GE just opened its new main office nearly San Jose and recruited a lot of engineers from Google, Apple, Microsoft with background of electrical engineer to develop its own system  called “Predix”, which is the world’s first and only cloud-based operating system for industry. GE plans to make “Preix” as the industry standard similar to the position of Microsoft Windows system in the PC industry. It will realize the digitalization and automation of the industry, including the oil and gas industry. One example for this trend is on June 14,2016, GE and Technip signed memorandum of understanding to explore digital solutions for new LNG projects. LNG will have great potential for growth as the world’s demand rises. So this prosperous area will be co-developed by the combination of strength of GE and Technip. GE will provide it reliable equipment solutions for the global LNG facilities, through sensors, advanced analytics and diagnostic expertise. Technip will provide unique expertise in EPC for LNG projects.

gn-solids-america-about

The future of the oil and gas industry will be more efficient and powerful, which will be realized by digital and automation and will optimize the equipment and operation to improve the productivity and cost-efficiencies.

As the crucial part of the mud cleaning system of the oil and gas industry, solid control system will also inevitably follow the trend of automation and digital, including its shale shaker, desander, desilter, mud cleaner, decanter centrifuge, mud agitator, cuttings dryer  and some other equipment and parts. GN solids control can manufacture the most advanced solid control equipment in the industry, such as the VFD controlled equipment which can realize the automation and digital. Welcome to log in to our website www.gnsolidsamerica.comto check more about the product info and send your inquiries to usa@gnsolidscontrol.com.

 

Share

written by Decanter Centrifuge \\ tags: , , , , , ,

Jun 13

Days and nights ago, GN Solids Control cooperated with an outdoor workforce and held an activity with suburb Beijing for a at some point journey. GN sales team gone to this journey and the quest was fruitful and substantial.
Marketing department is a very essential department of GN firm, this department is put together by more than twenty childhood who have a same objective and dream. This division includes three teams, the actual domestic sales team, the oversea market sales team and the marketing and advertising team, their duty isn’t only to get orders for the corporation, but also to collect information on the industry, receive feedbacks along with tips from clients and in addition takes some responsibility for that after sale service to the clients. Most of their period is spent on work.
Yet work shouldn’t be the just content of their life, and also work is also fun. GN Solids Control’s products are released to more than 60 nations and regions in the world, as well as for every time zone, there are GN’s clients. GN solids control has department offices and companies with USA and Russia and also GN agents are in a lot of countries. So GN income are working per different timezones and always on business holiday out of the country or from the city. It is not easy to get a re-union for everyone. GN can provide mud mixing system , mud cleaner, shale shaker , decanter centrifuge, mud agitator, mud tank ,shear pump, shaker screens ,etc.
This time, when we acquired this journey, there are still seven members are absent. GN team sent greetings photos to them to share the joy.

160526-GN-Outdoor-Training-1
With this journey, there are several activities assemble, it is not only test and contend for everyone’s IQ and also EQ, but also, a challenge with regard to everyone’s courage and staff work attitude. All challenges required a good team perform and cooperation. When we are only, we can not finish some of them, even without thinking of it. Nevertheless we work together, we confront the same problem and we provide for the solution, we accomplished all of them.
It’s just like the daily do the job, when we get together and discuss our ideas and experience, it would be easier for us for the most powerful solution and make the full using our resources. Only this way, could our team be more robust and tougher.
Well done, and we’ll do better.

Share

written by Decanter Centrifuge \\ tags: , , , , , ,

Jun 07

New environmental regulations are more focusing on the final disposal of drilling waste cutting. Normally there are several methods for final treatment of the drilling waste management . Cuttings Re-injection is also one of the main methods. In many developed countries like USA, Canada and Germany, cuttings re-injection technology is already very mature. China drillers are now more and more adopting this technology for final treatment on drilling cuttings.

Cuttings Re-injection system is always including 3 parts as cuttings transferring, cuttings screening and Cuttings Re-injection. In the first stage for cuttings transferring, there are shale shakers, centrifuge and other traditional solids control equipment doing the same job for drilling fluids recycling. The cuttings discharged from the shale shaker will be collected by the screw conveyor and then transferred to a Venturi device to fast transferring to the storage tank. Here the centrifugal pump will be equipped for shearing the cuttings. In mud mixing system, a fine mesh screen shaker will be here for screening the cuttings suitable for re-injection to underground. The injection pump is triplex cylinder type with pressure around 40MPa. With cuttings fed by the centrifugal pump, the injection pump would pump the cuttings back to the underground via the well.

160520ContainerCuttingsDryer

The well for re-injection could be either a new drilled one or an old well. Always a new one would be better to avoid the cuttings leak into the oil production layer. The re-injection layer could be under or above the production layer. This technology requests accurately analysis on the geological condition as not everywhere could be chosen as a point for cuttings re-injection.

Driller need choose the cuttings disposal method according to specific condition. Cuttings re-injection is a very good method for offshore drilling cuttings disposal, as it will save much time on shipping the cuttings back to onshore plant for treatment. Especially the application of SBM makes the base liquid is biodegradable for better environmental protection.

Share

written by Decanter Centrifuge \\ tags: , , , ,

May 17

If you would like to meet GN solids control at acrylic exhibition in 2016, this is contact sales@gnsolidscontrol. com for the appointment.
For Japan, Middle east and other nations around China, pls stop by at CIPPE 2016 throughout Beijing, China during Mar 29~31th. We will show the is among the most solids control equipments as well as drilling waste management gadgets as below:
Cuttings grasp dryer with telescopic skid
Drilling waste decanter centrifuge with telescopic skid
Gold mining centrifuge
Hi-G dryer shaker
Cuttings solidification unit
Solids control shale shaker
Solids control mud cleaner
Shaker screens
Dewatering unit
We now have a 272m2 booth on E2 hall, because our manufacturer is quite closed to the exhibit center, only 50 minuted drive by car, and we take all of our main tools there to show.

IMG_5263 If you are pretty busy in March, this is visit us at SIPPE 2016 in Shanghai this December.
If China is too not even close to your countries, like the clents from South America, Northern America, Middle east, The african continent, welcome to visit us at OVER-THE-COUNTER 2016 in Houston, ARIZONA at the beginning of May. We have a couple of stands there,
GN Sales space No . 1: Reliant Facility 1652-A
GN Booth Number 2: Reliant Arena 9732
Our professional sales engineer will highlight the unique technology of our straight cuttings dryer and VFD decanter centrifuge, and four -panel shale shaker.
A result of the low oil price in addition to slow oil industry, a number of clients cancelled the global oil show visit program, and will mainly focus on the particular professional oil show of their own country. You can satisfy GN at the specific event below:
(1) In India:
(2) In Iran
(3) In Russia
(4) In Malaysia
(5) In singapore:
(6) In Canada
(7) In Abu Dhabi
If you are convenient to meet you for any of the exhibitions earlier mentioned, pls contact us freely.

Share

written by Decanter Centrifuge \\ tags: , , ,

Mar 31

Recycle the drilling mud that lubricate the drilling bits.

The drilling mud solids control system is for filter away danger solids phase that contain in the drilling mud and reuse the needed solid phase.  The task is to keep drilling fluids in stable performance status.  There are several machinery that will need to perform the tasks.

The result of consist performance of drilling mud is avoid the blocking and damage of the oil and gas channel. It reduce the well drilling torque and friction drag and reduce the pressure oscillation of the annular air suction.  It also increase the velocity of the well drilling, extend life of the drill bit, reduce wear of the equipment.

drilling mud system

There are  five steps of filtering process that require five solids control machinery that will do  filter screening, degassing the mud, desanding the mud, desilting the mud, centrifuge force separation and demand of weighting up mud. The consist work flow between every solids control equipment use in the whole system is very important.   Level one to five level of output of the mud should be matched each other and the interval of separation size should be appropriate and have a certain overlap.  The result of the smaller solids which are not filter by the upper can be filter in the next controlled level.

With the development of well drilling technology, mud mixing system plays an important role in drilling operation. The various kinds of solids control systems function at the same time. Regardless the different kind of the solids control system, it’s basic function will not changed. It is depend on organic combination of mechanical removal equipments, drilling fluid mud tanks and other auxiliary equipments to accomplish the basic function:  Recycle the drilling mud that lubricate the drilling bits

Share

written by Decanter Centrifuge \\ tags: , , , , ,

Mar 23

Hebei GN Solids control company LLC is actually China leading manufacturer with regard to drilling mud solids control equipment and drilling waste management gear. Its brand name is GN Solids Control.
GN Solids control offers one quit solution for drilling device fluids, from mud solids control until the drilling waste management treatment system.
Since the first API certified solids control manufacturer from China, GN Solids Control aims upon China top market and also the international market. 70% associated with GN Solids Sales is actually from international market. GN Solids Control keep enhancing to cater for the higher as well as higher request of the worldwide market clients. With its quick development, GN Solids Control is among the leading solids control mafanucturers from all over the world as well as establish a famous brand: GN Solids Control.

new website
In order to offer a much more efficiency services to customers, GN Solids Control upgraded the company website, to offer a much better visual effect website. It can match for the mobile reading gear.
The new website of GN Solids Control is much more legible. And the new menus may hopes the visitors to discover the suitable equipment and information much more fast.
Further more, GN Solids Control upgrade its logo. All equipment documents as well as new equipment will start to make use of the new logos from now on.
Beneath is some of the advantages of GN Solids Control
1) GN is the First API licensed solids control equipment producer coming from China.
2) GN Solids America LLC is the first UNITED STATES based solids control organization from China.
3) No . one in China for immediate exporting of mud solids control and drilling waste materials management equipment. GN Services happen to be exported to over 60 nations and regions, with spouses and branches in UNITED STATES, Australia, Latin America, Center East, Africa etc .
4) GN Owns over ten patents for solids control and drilling waste management equipment.
GN offers one-stop and turn-key solution with regard to solids control and going waste management.
GN maintains research and develop the very best technology to manufacture high quality Shale shaker, mud cleaner, desander, desilter, vacuum degasser , mud mixing system ,mud tank system, mud agitator, bottom mud gun, shear pump , decanter centrifuge, vertical G cuttings dryer for our clients.

Share

written by Decanter Centrifuge \\ tags: , , , , , ,

Mar 07

It is well known that nowadays the technology is the first productivity. It is meaning that, with the developments of technology and the changing requests of human beings, only keeping the innovation would makes a corporation living longer. Just like currently recession in oil business, to live longer, so many corporations have to announce the bankrupt, or mergerred by other company. No one in this industry dare to say their business is still flourishing as ever before. More or less they will feel depressed to the gloomy prospect.

During the nearly 10 year’s development, GN never gave up the innovation process, and much was invested into this job. Keeping the eyes on the updating of new technology, and doing as much efforts as on independent innovation make GN gradually stepped into the leader ranks of the drilling waste management equipments manufacturers.

At the beginning of GN’s foundation, 2 workshops and several workers manufactured the first unit shale shaker. That time, centrifuge is just a dream to GN. No orders, unstable performance, and other problems were in the way of GN development. Luckily, GN overcome all the difficulties and couples years later, GN Solids Control moved to a new facility with larger workshops and brand new caging rooms as offices. It is here, in the new facility, GN gained much and came across a flourishing in the oil markets, and not so many competitors. With the perfection of GN’s production quality and increasing of manufacturing efficiency, many orders come to GN. It is during this period, GN got the reputation in world market and we could make all the equipment relative to drilling fluids recycling. Here born the first unit GN self-design and manufactured decanter centrifuge, and it was the best seller that time. GN gradually becomes someone in China solids control industry.

drilling mud system

After moving to Beijing new factory, GN got 5-floor office building and new large workshops. CNC lathe was brought into our manufacturing processing. Working efficiency was greatly increased and the working pieces are much more accurate. The following recession finalized many small businesses. It is GN’s keeping innovation that saved GN in the winter, with the downhill request on normal solids control equipment, GN’S dewatering system, drilling waste cuttings management system, and even the cuttings solidification unit guaranteed the orders to GN. Nowadays, GN is able to provide both normal drilling fluids mud mixing system and cuttings final disposal solutions to meet customers’ request.

Future is not predictable at this time, however, we believe so long as we could keeping the way on independent innovation and look optimistically forward, we will get we are looking for.

Share

written by Decanter Centrifuge \\ tags: , ,

Mar 01

Yesterday, GN’s manufacturing department done the fabrication of a mud mixing tank with increase hoppers. Mud mixing tank is widely used in the drilling mud system regarding mixing and re-configuration the actual drilling fluids. Also this will be used for storage the particular active drilling fluids.

mud mixing system
The mud mixing system is actually consisting of mixing tank, mud agitators, mud guns, mixing pump and mud hoppers. Usually, the mixing pump as well as the mud hopper will be situated at one end with the mud tank to make the mixing tank system a compact and also single unit, while in a few projects, the mixing pump and hopper are installed on another skid so that the mixing tank and the jet mud mixer could be used much unhampered. The picture in this article shows that the particular jet mud mixer skid was located at 1 side of the mixing mud tank. There are one mixing pump and 2 mud hoppers on the skid. The mixing pump is connected with the two hoppers, one of the hoppers is needed for mixing barite to create weighted drilling fluids, plus the other one is used for including bentonite into the drilling liquids.
There is a steel frame about second hopper with iron bars over the hopper. This specific horizontal steel bar is needed to hang the bentonite handbag which will be hooked at several corners of the steel structure to make it easier for adding typically the bentonite powder into the hopper. It is worthy to mention the fact that steel bar is with forklift lifting slot so that the club with bentonite bags may be lift and put on the shape by a forklift to save man power.
This mud mixing system is with a control panel to control mixing pump which could transfer mud to both hoppers. Around the mixing tank, there is one more charge pump which is used to help transfer the active mud back to the rig with regard to reuse.

Share

written by Decanter Centrifuge \\ tags: , , ,